Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Sat Dec 21, 2024 12:19 pm

View unanswered posts | View active topics


Board index » Thorp T-18 » Trim Systems

All times are UTC - 6 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
MartyG
PostPosted: Thu Nov 03, 2022 10:07 am 
Newbie
Newbie
User avatar

Joined: Mon Jun 07, 2021 8:29 pm
Posts: 48
Location: Y51 - Viroqua, WI
I have electric elevator trim and either a roll pin or shear pin broke that connects the electric motor and the trim jackshaft. It looks like it just wore down over time rather than there being some sort of event that caused the shear. The hole seems to be just a hair smaller than 1/16" in diameter. Does anyone know the correct part to replace this pin? The stamping on the motor is hard to read, but from what I can see it looks like it says "Barber-Coleman FYQM33610-1"

_________________
Marty G
N50LE
YouTube Channel
martygrosse@yahoo.com
Top
 Profile  
 
leewwalton
PostPosted: Thu Nov 03, 2022 3:50 pm 
Administrator
Administrator
User avatar

Joined: Tue Oct 20, 2009 4:09 pm
Posts: 1715
Images: 107
Location: Houston, TX
I'd probably go to the hardware store and find an appropriately sized roll pin

_________________
Lee Walton
Houston, TX
N51863,N118LW
KEFD
Top
 Profile Personal album  
 
MartyG
PostPosted: Fri Nov 04, 2022 8:43 am 
Newbie
Newbie
User avatar

Joined: Mon Jun 07, 2021 8:29 pm
Posts: 48
Location: Y51 - Viroqua, WI
Thanks Lee. I just wanted to make sure there wasn't some specific reason not do do that.

_________________
Marty G
N50LE
YouTube Channel
martygrosse@yahoo.com
Top
 Profile  
 
pmandel
PostPosted: Sun Nov 06, 2022 9:03 pm 
Jr. Member
Jr. Member

Joined: Fri Oct 25, 2019 8:00 pm
Posts: 98
What Lee said. Mine broke as well, with the stabilator trim full up during takeoff. That was an interesting ride. Forward pressure the whole way 'round the pattern to landing.

My A&P pushed out the remnants of the old pin and shoved in a new one, nothing special, just a NAPA or hardware or similar store. Bring the old one with you for sizing.

_________________
Philip Mandel
N118BC
S/N 957
Beaverton OR
Top
 Profile  
 
fytrplt
PostPosted: Tue Nov 08, 2022 5:19 pm 
Hero Member
Hero Member
User avatar

Joined: Tue Oct 20, 2009 8:07 pm
Posts: 1153
Images: 2
Location: Lakeland, Florida, USA
Might consider using a cotter pin. Easier to replace.

_________________
Bob Highley
N711SH
SN 835
KLAL
Top
 Profile Personal album  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Thorp T-18 » Trim Systems

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 4 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  

[ Time : 0.096s | 10 Queries | GZIP : On ]