Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Thu Mar 28, 2024 3:18 pm

All times are UTC - 6 hours [ DST ]




Post new topic Reply to topic  [ 20 posts ]  Go to page 1, 2  Next
Author Message
MarcG
PostPosted: Thu Dec 08, 2022 8:46 am 
Newbie
Newbie

Joined: Sat Aug 29, 2020 2:05 am
Posts: 28
Hi Guys,

My Thorp project is progressing slowly, but at least it is progressing.

My tailwheel is rather worn, and I was hoping for recommendations on the best tailwheel for the Thorp. I will be landing on both grass and asphalt runways.

Any advice is appreciated!

Thanks,

Marc


Top
 Profile  
 
James Grahn
PostPosted: Thu Dec 08, 2022 10:18 am 
Hero Member
Hero Member

Joined: Sat Oct 24, 2009 7:16 pm
Posts: 1434
Images: 0
Location: USA
Aviation Products double fork six inch on a 5/8” tapered rod spring.
Cubes


Top
 Profile Personal album  
 
MarcG
PostPosted: Thu Dec 08, 2022 7:10 pm 
Newbie
Newbie

Joined: Sat Aug 29, 2020 2:05 am
Posts: 28
Thanks Cubes! Much appreciated


Top
 Profile  
 
bfinney
PostPosted: Sun Dec 11, 2022 3:15 pm 
Sr. Member
Sr. Member
User avatar

Joined: Thu Oct 22, 2009 2:24 pm
Posts: 501
Images: 6
Location: Yelm, WA USA
I'll second what Cubes said. 8)

_________________
Bruce Finney
N18JF T-18C #262
Yelm, WA USA


Top
 Profile Personal album  
 
Rich Brazell
PostPosted: Sun Dec 11, 2022 6:44 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3095
Images: 64
Location: Jamul, CA (San Diego area)
If you use the Aviation Products wheel the first thing you do is shit can the standard wheel bearings that come with the wheel and get a Timken set of quality bearings or their equivalent .

RB O0
NX115RX


Top
 Profile Personal album  
 
Jim Mantyla
PostPosted: Mon Dec 12, 2022 10:45 am 
Sr. Member
Sr. Member

Joined: Wed Oct 21, 2009 6:57 pm
Posts: 227
Location: Barrie, Ontario,Canada
I third what Cubes recommends. I swapped my wheel out for a pneumatic one.

Jim


Top
 Profile  
 
jtwigg
PostPosted: Tue Dec 13, 2022 8:52 pm 
Sr. Member
Sr. Member
User avatar

Joined: Thu Sep 03, 2015 10:11 pm
Posts: 192
Images: 0
How is the tapered rod attached to the aircraft? I need to replace my Maule tailwheel as well.

_________________
John Twigg N12055 SN.79 Pittsburgh, PA (KFWQ)


Top
 Profile Personal album  
 
bfinney
PostPosted: Wed Dec 14, 2022 3:28 am 
Sr. Member
Sr. Member
User avatar

Joined: Thu Oct 22, 2009 2:24 pm
Posts: 501
Images: 6
Location: Yelm, WA USA
Here's a photo of the old spring and Maule tailwheel as it came off of my aircraft, calling it a "spring" is being kind.
Image

Here's the new Trusty spring and AViation Product double fork 6" tailwheel. Note the bolster at the front end of the spring, this should be the same as called out on drawing A-862. No mods were made to the aircraft. Since my aircraft did not have the bolster, Tom Hunter made me a deal and included a bolster with the tailwheel and spring
Image

Hope that clears things up, clear as mud eh! 8)

Note on Rich's comment on bearings, I've had my tailwheel on the aircraft since Dec 2008 and have not had to change bearings. That said I read some time ago that an airplane pieces part vendor was sourcing the tailwheels without bearing and installing el-cheepo bearings. Also stated that the wheels that came straight from Aviation Products were quality bearings. I don't remember the source of this statement so it's worth what you paid for it.

Disclaimer - your mileage may vary. ;D

_________________
Bruce Finney
N18JF T-18C #262
Yelm, WA USA


Top
 Profile Personal album  
 
jtwigg
PostPosted: Fri Dec 16, 2022 5:27 am 
Sr. Member
Sr. Member
User avatar

Joined: Thu Sep 03, 2015 10:11 pm
Posts: 192
Images: 0
That’s exactly my tailwheel. I don’t see, however, how your new tailwheel has the three attach points like the Maule tailwheel had. Is that what the “bolster” is? I’m not familiar with that term.

_________________
John Twigg N12055 SN.79 Pittsburgh, PA (KFWQ)


Top
 Profile Personal album  
 
Hagle347
PostPosted: Fri Dec 16, 2022 11:51 am 
Sr. Member
Sr. Member
User avatar

Joined: Tue Oct 26, 2010 3:42 pm
Posts: 566
Images: 19
Location: USA
Hey John, the parts that Cubes will sell you include everything you’ll need to bolt the new spring to the aircraft.
The advantage you will find is that the new tail spring drops the tail of the airplane an inch. Allowing for a better 3 point landing attitude. That and it’s not as stiff as the original half trailer spring style. And then there’s the “less drag” , goes faster discussion….
You will find it’s a definite upgrade!
T


Top
 Profile Personal album  
 
James Grahn
PostPosted: Fri Dec 16, 2022 4:22 pm 
Hero Member
Hero Member

Joined: Sat Oct 24, 2009 7:16 pm
Posts: 1434
Images: 0
Location: USA
It also moves the tail wheel 9” aft, which helps a little with over correcting.
John, the front end of the spring has a hole that the AN6 bolt goes through. There is a small washer to keep the spring parallel to the belly skin. As you move aft, there is a collar that slides on the spring. The collar has two ears that the AN4 bolts go through. You also have to drill a 5/16” hole laterally to install an AN5 bolt (not on your Maule spring) that keeps everything from rotating.
Cubes


Top
 Profile Personal album  
 
James Grahn
PostPosted: Fri Dec 16, 2022 4:25 pm 
Hero Member
Hero Member

Joined: Sat Oct 24, 2009 7:16 pm
Posts: 1434
Images: 0
Location: USA
John, look under your plane at the aft spring. There is a 1/4” aluminum plate that the spring bolts go through. That is the bolster. Every plane should have one. If you don’t, I have them.
Cubes


Top
 Profile Personal album  
 
dickwolff
PostPosted: Fri Dec 16, 2022 6:31 pm 
Sr. Member
Sr. Member

Joined: Tue Nov 24, 2009 7:40 pm
Posts: 498
Images: 6
Location: Canada
Owners should look at that bolster plate once in a while. On my last T18 it was quite badly corroded between the plate and the skin.

D


Top
 Profile Personal album  
 
jtwigg
PostPosted: Sat Dec 17, 2022 4:01 pm 
Sr. Member
Sr. Member
User avatar

Joined: Thu Sep 03, 2015 10:11 pm
Posts: 192
Images: 0
Thanks, guys! I was concerned that I’d have to make changes to the fuselage structure.
Let’s talk when you have a moment, Cubes, to hook me up.

_________________
John Twigg N12055 SN.79 Pittsburgh, PA (KFWQ)


Top
 Profile Personal album  
 
AHK
PostPosted: Mon Dec 26, 2022 10:39 am 
Newbie
Newbie

Joined: Mon Feb 07, 2022 3:54 pm
Posts: 3
Dick Wolff…I agree. I pulled mine off because I could see a little white powder at one edge of the bolster plate where it touched the fuselage skin. When I took it off, there was definitely significant corrosion on the bolster plate itself with some pitting. Luckily the skin of the fuselage wasn’t corroded. I painted the bolster itself after sanding smooth, flipped it over for good measure before reassembling. My point is you’re right. It wasn’t easy to see what was going on. I’ve thought about maybe cutting a thin nylon spacer to separate the two and hopefully eliminate electrolysis. Any thoughts?


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 20 posts ]  Go to page 1, 2  Next

All times are UTC - 6 hours [ DST ]


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

[ Time : 0.193s | 13 Queries | GZIP : On ]