Thorp Air Command - T18.net

Supporting Owners, Builders and Pilots of the Thorp T-18 and its variants.
It is currently Mon Dec 23, 2024 7:40 pm

View unanswered posts | View active topics


Board index » Thorp T-18 » Projects

All times are UTC - 6 hours [ DST ]



Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 
  Print view Previous topic | Next topic 

Should I repaint the intake pipe flanges? (2-day poll)
Poll ended at Mon Jun 12, 2017 9:38 pm
Yes, this is necessary because it may rust without paint 0%  0%  [ 0 ]
Yes, this is necessary 0%  0%  [ 0 ]
Optional - your choice 14%  14%  [ 1 ]
No, get it flying! 57%  57%  [ 4 ]
Other 29%  29%  [ 2 ]
Total votes : 7
Author Message
jtwigg
PostPosted: Sat Jun 10, 2017 9:38 pm 
Sr. Member
Sr. Member
User avatar

Joined: Thu Sep 03, 2015 10:11 pm
Posts: 192
Images: 0
Today I cleaned up parts of the engine. The gasket material on the air intake pipes was really stuck to both the pipe and the cylinder. In cleaning it off the pipe's flange, I removed any paint that was there. Should I repaint the flange? I'm trying out the Poll feature on this question; please comment and vote! O:-)


Attachments:
File comment: The intake pipes had this same gasket material stuck hard to them.
20170610_011843.jpg
20170610_011843.jpg [ 2.19 MiB | Viewed 6400 times ]
File comment: Cleaning off the gasket material removed the paint
20170610_222239.jpg
20170610_222239.jpg [ 1.59 MiB | Viewed 6400 times ]
File comment: Detail
20170610_222153.jpg
20170610_222153.jpg [ 1.08 MiB | Viewed 6400 times ]

_________________
John Twigg N12055 SN.79 Pittsburgh, PA (KFWQ)
Top
 Profile Personal album  
 
Rich Brazell
PostPosted: Sat Jun 10, 2017 10:22 pm 
Hero Member
Hero Member

Joined: Wed Oct 21, 2009 12:33 pm
Posts: 3108
Images: 64
Location: Jamul, CA (San Diego area)
I really think you need a "clean" mating surface . :P The Lycoming overhaul manual may shed some lite on this ? ???

RB O0
Top
 Profile Personal album  
 
1albee
PostPosted: Sun Jun 11, 2017 6:37 am 
Sr. Member
Sr. Member

Joined: Sat Oct 31, 2015 6:58 pm
Posts: 172
Images: 0
You don't paint the inside of the intake tube, so painting the face of the flange is not necessary. The end where the rubber tubes slip over the un flanged part of the tube I don't paint either, same with the oil pan tubes. If you don't hanger and tie down on a wind swept ocean beach you may see some corrosion.
Phil
118BC
Top
 Profile Personal album  
 
jtwigg
PostPosted: Tue Jun 13, 2017 10:26 pm 
Sr. Member
Sr. Member
User avatar

Joined: Thu Sep 03, 2015 10:11 pm
Posts: 192
Images: 0
Thanks, everyone, for your votes and comments. If you saw the results, 4 out of 7 votes were to get her flying. So, I've decided not to paint these tube flanges. I sanded them with a fine sanding block and they are very smooth and should seal well. That's good enough for me. Thanks again!

_________________
John Twigg N12055 SN.79 Pittsburgh, PA (KFWQ)
Top
 Profile Personal album  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 4 posts ] 

Board index » Thorp T-18 » Projects

All times are UTC - 6 hours [ DST ]

Who is online

Users browsing this forum: No registered users and 7 guests

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
cron

[ Time : 0.119s | 13 Queries | GZIP : On ]